• <legend id="8xv0q" ></legend>
    <th id="8xv0q" ></th>
    <code id="8xv0q" ></code><b id="8xv0q" ></b>
    <rt id="8xv0q" ></rt>
        <pre id="8xv0q" ><li id="8xv0q" ></li></pre>
          <bdo id="8xv0q" ></bdo><big id="8xv0q" ><listing id="8xv0q" ></listing></big>

          <li id="8xv0q" ><acronym id="8xv0q" ></acronym></li>
          1. <nobr id="8xv0q" ><var id="8xv0q" ></var></nobr>

            <xmp id="8xv0q" >
            博赢彩票app下载 公司|博赢彩票app下载简介 产品展示 热卖产品 公司|博赢彩票app下载博赢彩票app下载 技术文章 人才招聘 资料下载 联系博赢彩票app下载
            主营产品: 检测仪器

            产品目录 更多...
            推荐产品 更多...


            点击次数:177 发布时间:2019-09-26

            上海鼎徵仪器仪表设备有限公司|博赢彩票app下载 蒸汽喷射试验机满足测试规范汽车厂家:宝马 、奔驰 、通用 、大众 、福特 、沃尔沃等规范(AA-0136 、DIN 55662 、ISO16925,DBL 7381,GM9531P 、PV1503 、VOLVO STD 423-0015,VOLVO VCS 1029 54719 、FLTM BO 160-04 、MS210-07PSA D23 5376,Renault D25 2018/-A-2001 ,GMW16745-2012方法B,TPJLR-52.561-2009

            1 Scope  上海鼎徵仪器仪表设备有限公司|博赢彩票app下载
            This International Standard specifies a test method for the assessment of the resistance of coatings to
            pressure water-jetting. The test method simulates the effects pressure water-jetting has on a coating.
            5 Apparatus and materials
            Ordinary laboratory apparatus, together with the following:
            5.1 Pressure water-jet, consisting of a high-pressure pump and a nozzle.
            A high-pressure pump conveys the water from a storage bin. To avoid influences from variations in
            pressure, it is necessary that the pressure and the volumetric flow rate be adjustable at the nozzle
            described below.
            The water temperature shall be adjustable to ± 2 °C.
            The temperature shall be adjusted in accordance with Annex A. Necessary safety devices on the pressure
            side of the unit, as e.g. pressure relief valve and by-pass valve, shall exist. If the jetting is unsteady, a flow
            calming section may be installed in front of the nozzle. A pulsation of the water jet at the opening of the
            pump is inadmissible. In order to reach a reproducible result, the nozzle shall be solidly mechanically
            fixed and the test specimen shall be secured against slipping. For the adjustment of the volumetric flow
            rate, a nozzle with a jet angle of 25° and a volumetric flow rate of 6 l/min at 2 MPa (20 bar) is required
            (see Annex A).
            The following technical data should be attainable:
            — volumetric flow rate: 8 l/min to 14 l/min
            — pressure: 4 MPa (40 bar) to 13 MPa (130 bar)
            — temperature: 20 °C to 80 °C
            — jetting time: 10 s to 300 s

            Figure 1 shows the schematic construction of a pressure water-jet apparatus which is specially built for these tests.
            1 flow calming section
            2 high-pressure valve, height adjustable
            3 test specimen
            4 clamping element  
            5 feed tank
            6 floating valve with filter
            7 water shortage safeguard
            8 heating
            9 base frame, moveable
            10 temperature sensor  
            11 high-pressure pump
            12 by-pass valve  
            13 pressure relief valve
            14 pressure transmitter
            8.1 Introducing the cut or the scribe  上海鼎徵仪器仪表设备有限公司|博赢彩票app下载
            Make sure that the test specimen is securely fastened when introducing the cut or the scribe.
            Introduce both of the cuts or scribes vertically through the coating into the substrate using the cutting
            or scribing tool, as shown in Figure 2. The depth of the cut or scribe into the substrate should be as
            minimal as possible. The length of the first cut or scribe shall be at least 100 mm, if the geometry of the
            part allows that. At an angle, introduce a second cut or scribe with a minimum length of 20 mm. The
            cuts or scribes shall be introduced straight-line at an angle of approximately 30°. An automatic cutting
            or scribing device may be used. Residues of the coating shall be removed from the cut or scribe.
            NOTE The depth of the cut or scribe into the substrate influences the result.
            The cutting or scribing tools should be checked regularly and replaced if necessary.

               Figure 2 — Introducing the cuts or scribes (St Andrew’s cross)

            8.2 Testing
            After inserting the test specimen into the apparatus (e.g. using a spacer block), calibrate the space
            between test specimen and nozzle.
            Operate the pressure water-jetting apparatus at room temperature.
            Three test methods (A, B, or C – see Table 1) are preferred as well as three possible scribing tools (C, L, or
            S – see 5.3). The test method to be applied, the scribing or cutting tool to be used, and the water pressure
            shall be agreed.
            Table 1 — Test methods  上海鼎徵仪器仪表设备有限公司|博赢彩票app下载

            Test methodWater Temperature
            Impact angle Space between nozzle and sample mmFlow rate
            Duration of

            For jetting, deionized water should be used.
            When using automatic and manual devices, fasten the test specimen so that the water jet impacts as
            shown in Figure 3. The jet impacts in the middle above the point of intersection onto the longer one of both cuts/scribes.

            Figure 3 — Jetting area

            9 Evaluation
            9.1 General
            Damage is recognizable when the coating loosens or flakes, regardless of which coat sustains the damage.
            9.2 Evaluation with pictures to compare
            Carry out the evaluation visually, comparing the specimen with the pictures.
            In the course of the visual evaluation, a characteristic value is laid down by comparing with the
            illustrations in Figures 4 to 9. A characteristic value between 1 and 5 results, depending on the degree
            of damage. No damage corresponds to the characteristic value 0. In addition to the evaluation, if
            applicable, the attribution of the separation from the main separation level or to the respective film
            shall be indicated.
            The result of the visual assessment is indicated in dependence of the applied method, for example:
            — method A: characteristic value A;
            — method B: characteristic value B;
            — method C: characteristic value C.
            NOTE In addition, by measuring the areas of flaking (maximum width, in millimetres, or area, in square
            millimetres), the overall damage can be evaluated. The overall damage is calculated by summing up all damaged
            areas of the test specimen. Even the smallest areas of flaking are measured and calculated, and all areas added to
            the overall damage.

            Figure 5 — Characteristic value 1 for pressure water-jet damage

            Figure 6 — Characteristic value 2 for pressure water-jet damage

            Figure 7 — Characteristic value 3 for pressure water-jet damage

            Figure 8 — Characteristic value 4 for pressure water-jet damage

            Figure 9 — Characteristic value 5 for pressure water-jet damage

            Annex A
            Calibration of the test apparatus
            A.1 Apparatus and materials
            Ordinary laboratory apparatus, as well as the following.
            A.1.1 Temperature measuring device, with sensor, capable of measuring to 0,5 °C.
            A.1.2 Balance, weighing to 10 g.
            A.1.3 Time measuring device (stopwatch), capable of measuring ± 0,1 s.
            A.1.4 Container, for the determination of the volumetric flow rate for at least 20 l of water.
            A.1.5 Plastic block, made of polystyrene rigid plastic foam.
            The kind of the polystyrene rigid plastic foam shall be agreed by the interested parties.
            A.1.6 Length measuring device, capable of measuring ± 0,1 mm.
            A.2.4 Calibration of the water jet
            The conditions for the calibration of the jetting are in accordance with method B. For the calibration of
            the jetting, a stainless steel precision flat film extrusion die with a volumetric flow rate of the nozzle of
            6 l/min at 2 MPa (20 bar) and a jet angle 25° is used. This nozzle is required to produce an even liquid
            distribution during the entire jetting.
            When using an automatic pressure-water apparatus, fasten the polystyrene rigid plastic foam in the
            apparatus so that the jet cannot move the block. When using a manual apparatus, fasten the block in a
            similar fixture.
            After jetting, the length and the width of the impact are measured. See Figure A.1.
            The mean length of the impact shall be (73 ± 5) mm and the mean width (8 ± 1) mm on average.

            Figure A.1 — Measures of the washed-out areas in the polystyrene rigid plastic foam

            博赢彩票app下载 | 公司|博赢彩票app下载简介 | 产品展示 | 热卖产品 | 公司|博赢彩票app下载博赢彩票app下载 | 技术文章 | 人才招聘 | 资料下载 | 联系博赢彩票app下载

            友情链接:乐福彩票 新疆体彩网 澳客体彩网 宁夏体彩网 好运彩 彩吧注册

            上海鼎徵仪器仪表设备有限公司|博赢彩票app下载 博赢彩票app下载版权所有 地址:上海市嘉定区德富路1198号803室太湖世家国际大厦
            联系人:谢文清 电话:86-21-32535037 手机:13472521719 传真:86-21-32535039 邮编:200070 邮箱:422355329@qq.com
            技术支持博赢彩票app下载: ICP备案号:



          2. <legend id="8xv0q" ></legend>
            <th id="8xv0q" ></th>
            <code id="8xv0q" ></code><b id="8xv0q" ></b>
            <rt id="8xv0q" ></rt>
                <pre id="8xv0q" ><li id="8xv0q" ></li></pre>
                  <bdo id="8xv0q" ></bdo><big id="8xv0q" ><listing id="8xv0q" ></listing></big>

                  <li id="8xv0q" ><acronym id="8xv0q" ></acronym></li>
                  1. <nobr id="8xv0q" ><var id="8xv0q" ></var></nobr>

                    <xmp id="8xv0q" >